
SikaBond® AT Metal
SikaBond® AT Metal is a 1-component, solvent-free, non-corrosive adhesive for metal bonding.
- Silicone-free
- Non-corrosive
- Very good workability
- Short cut off string
- Good initial tack and fast curing
- Good adhesion on porous substrates
- Good weathering and water resistance
- Very high adhesive strength without priming on many metals and non-porous substrates
Usage
SikaBond® AT Metal is designed for the internal and external bonding of metal facade and roof elements, roof coverings, cover plates, metal sheets, sky lights and metal cladding.Advantages
- Silicone-free
- Non-corrosive
- Very good workability
- Short cut off string
- Good initial tack and fast curing
- Good adhesion on porous substrates
- Good weathering and water resistance
- Very high adhesive strength without priming on many metals and non-porous substrates
Packaging
300 mL cartridge, 12 cartridges per box
Colour
Copper, light-grey
Product Details
APPROVALS / CERTIFICATES
- ISO 11600 F 20 HM
Composition
Silane terminated polymer
Shelf life
SikaBond® AT Metal has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met.
Storage conditions
SikaBond® AT Metal shall be stored in dry conditions, protected from direct sunlight and at temperatures between +5 °C and +25 °C.
Density
~1.35 kg/L |
Shore A Hardness
After 28 days | ~38 |
Tensile Strength
~1.6 N/mm2 |
Secant Tensile Modulus
After 28 days (at +23 °C) (100 % elongation) | ~0.70 N/mm2 |
Elastic Recovery
After 28 days | ~70 % |
Lap Shear Strength
~1.15 N/mm2, 1 mm adhesive thickness | (EN 1465) |
Tear Propagation Resistance
~5.5 N/mm | (ISO 34) |
Chemical Resistance
SikaBond® AT Metal is resistant to water, seawater, diluted alkalis, cement slurry and water dispersed detergent.
SikaBond® AT Metal is not resistant to alcohols, organic acids, concentrated alkalis and concentrated acids, chlorinated and aromatic hydro-carbons.
SikaBond® AT Metal is not or is only temporarily resistant to concentrated mineral acids, organic solvents (ketones, esters, aromatics) and alcohol, lacquer and paint thinners, organic acids and caustic solutions or solvents.
For detailed information please contact our Technical Service Department.
Service Temperature
−40 °C to +90 °C
Application
Sag Flow
0 mm (20 mm profile, 23 °C) | (ISO 7390) |
Ambient Air Temperature
+5 °C to +40 °C, min. 3 °C above dew point temperature
Relative Air Humidity
30% to 90%
Substrate Temperature
+5 °C to +40 °C
Curing Rate
at +23 °C / 50 % r.h. | ~3 mm/24 h |
Skinning time
30 minutes approx. (23 °C / 50% r.h.) | (CQP 019-1) |
Consumption
Beaded / Cordon application:
44 ml approx. per linear meter (with triangular nozzle)
APPLICATION INSTRUCTIONS
For the application of SikaBond® AT Metal all standard construction guidelines apply.
SUBSTRATE PREPARATION
The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Paint, cement laitance and other poorly adhering contaminants must be removed. SikaBond® AT Metal adheres without primers and/or activators.
However, for optimum adhesion and critical, high performance applications, such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pre-treatment procedures shall be followed:
Non- porous substrates
Glazed tiles, powder coated metals, aluminium, anodised aluminium, stainless steel and galvanised steel have to be treated with a very fine abrasive pad and Sika® Aktivator-205 shall be applied using a clean towel. Before sealing allow a flash-off time of > 15 minutes (< 6 hours).
For frequent water contact or constant high relative air humidity use Sika® Primer-3 N for porous substrates (concrete, brick, etc.).
For titan-zinc and copper, use Sika® Aktivator-205 and Sika® Primer-3 N as adhesion promoters.
For detailed advice, please contact our Technical Service Department.
Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly.
CLEANING OF EQUIPMENT
Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® TopClean T. Once cured, residual material can only be removed mechanically.